CNCGLASS EVA Film as Safety Glazing Interlayer

These photographs show CNC EVA film as a safety glazing interlayer at packing and shipment: a wrapped Super Clear roll on a workshop scale, long EVA FILM cartons packed at the packing area, and outdoor pallets of cartons and wooden CNC crates labeled Super Clear, Sandblasting White, and Super Milky White. Enquiries can be sent to cnc@cncglass.com.

End of a wrapped CNC EVA FILM Super Clear roll, with the product label and a worker in a blue coat partly visible at right.
The same wrapped roll lying on a stainless steel scale table, with the wall-mounted digital scale reading 88.1 kg.
Closer view of the digital scale showing 88.1 kg and the end of the wrapped EVA film roll.
A worker in a blue coat and cap packing a long cardboard carton printed EVA FILM, at a packing table under a Packing Area sign.
The packed long EVA FILM carton on a steel table, with the end label visible and the packing-area sign and curtain in the background.
Close-up of the carton end label for CNC EVA FILM Super Clear, EVAFORCE EXTREMF, 0.76 mm by 2300 mm by 50 m, with the carton stenciled 235X25X25CM.
Outdoor pallet of brown cartons with red cnc@cncglass.com tape, in front of stacked wooden CNC crates labeled EVA FILM.
Wider view of the loading area, with cartons on a pallet, stacked CNC crates, and a truck at the far end of the lane beside the building.
Closer view of the brown cartons on the pallet, with red tape reading cnc@cncglass.com and some cartons labeled CNC EVA.
Close-up of a wooden crate with a red CNC plaque and a paper label for CNC EVA FILM Super Clear, EVAFORCE EXTREME, 0.76 by 2300 by 50, quantity 6 rolls, case no. 10-8.
Two wooden crates labeled CNC EVA FILM Sandblasting White, 0.38 by 2000 by 50, case no. 10-9, and CNC EVA FILM Super Milky White, both with CNC plaques.
Several stacked and single wooden crates stenciled EVA FILM in a courtyard, with an outdoor air conditioner on the wall to the right.

CNCGLASS EVA Film as Safety Laminated Glass Interlayer

These photographs show CNCGLASS EVA film as a safety laminated glass interlayer in the workshop: wrapped rolls on a stainless steel cart, film running over rollers on the production line, inspection of unrolled film on a stainless steel table, and workers packing wrapped rolls at a packing table. Enquiries can be sent to cnc@cncglass.com.

Two rolls of EVA interlayer film in clear protective wrap on a stainless steel cart in the workshop.
A single roll of EVA interlayer film in clear protective wrap on a stainless steel cart.
EVA interlayer film running over rollers on the production line, with a worker in a cleanroom suit at the far end of the machine.
Side view of the production line, with a roll of EVA interlayer film feeding over a steel roller and a support roller.
Close view of a roll of EVA interlayer film between steel rollers on the production line.
Close view of EVA interlayer film passing over a metal bar and rollers on the production line.
A worker in a cleanroom suit inspecting EVA interlayer film unrolled from a large roll on a stainless steel table.
Workers wrapping a roll of EVA interlayer film in clear protective film on a stainless steel table.
Two workers handling a wrapped roll of EVA interlayer film on a stainless steel packing table.
Two workers at a packing table with a wrapped roll of EVA interlayer film.
A worker operates the packing table while another holds a wrapped roll of EVA interlayer film.
A worker at the packing-table controls, with a wrapped roll of EVA interlayer film held in the foreground.
Two wrapped rolls of EVA interlayer film on a stainless steel cart.

Air-Cooled-Handheld-Electric-Thermal-Cutter-500C-Fabric-Cutting-Instruction-Manual

This CNCGLASS instruction manual describes the safe set-up, operation, cleaning and service conditions of the CNCGLASS air-cooled handheld electric thermal cutter, a portable hot-blade cutting tool for cutting and simultaneously sealing the edges of textile sheets such as curtain cloth, polyester fabric and sheer voile, so that cuts close cleanly without fraying. The cutter is an air-cooled, hand-held resistance-heated blade tool. Technical specifications listed in the manual are supply voltage AC 220 V, 50 Hz; maximum output power 130 W; maximum blade temperature 500 °C; tool body weight 610 g; tool body length 320 mm; an arc blade for fabric and synthetic textile cutting; and air-cooled handle construction. The standard package is the electric thermal cutter body, one arc cutting blade, one blade-installation spanner, one brass wire cleaning brush, and one plastic carrying case.

The manual states that the blade reaches the set temperature within seconds, and that cutting quality is best when blade temperature and hand speed are matched. It instructs the operator to unplug the power cord before installing the blade, to make a trial cut on a test piece before cutting production material, to use the tool indoors only in well-ventilated rooms, never to let the blade dry-burn when not cutting, and to clean residue with the supplied brass wire brush with the trigger released. A 12-month warranty applies from the purchase date shown on the invoice or receipt; consumable blades are excluded, and damage arising from use or storage contrary to the manual, or from non-original parts, is not covered. Enquiries can be sent to cnc@cncglass.com.

Sandblasting-White-EVA-Film-0.38mm-Performance-Summary

This CNCGLASS technical note summarizes in-house quality-control measurements for Sandblasting White EVA film, a 0.38 mm ethylene-vinyl acetate (EVA) interlayer for laminated safety glass. The film has a matte embossed (frosted) surface finish and is intended for outdoor laminated-glass applications. The note states that it is a CNCGLASS technical note and performance summary, not a third-party test certificate or a certificate of conformity, and that it does not authorize the use of any third-party laboratory mark.

For the un-laminated film, visible-light transmittance was 4.50% with one layer, 2.00% with two layers, and 1.50% with three layers; haze was 97.34%, 98.10%, and 98.13%; and UV rejection at 280-380 nm was 99.03%, 99.44%, and 99.60%. The note explains that the matte embossed surface scatters incident light, so direct visible-light transmittance of the un-laminated film reads low while haze reads correspondingly high; the embossing is absorbed during lamination, restoring visual clarity in the finished laminate. Ultraviolet rejection across 280-380 nm exceeds 99% at every layer count. Mechanical and physical properties reported for the film include Young’s modulus 9.7 MPa, tensile strength 14.8 MPa, elongation at break 601.2%, water absorption less than 0.1%, bond strength to glass 108 N/cm, and bond strength to PET greater than 40 N/cm. Gel content (crosslink degree) was 86.7%. The recommended lamination process is 80 °C for 20 minutes, then 120 °C for 60 minutes. Shelf life is eight months in sealed storage. Quality inspection of this product family is performed against EN 14449:2005 and EN ISO 12543-4:2011. Enquiries can be sent to cnc@cncglass.com.

CNCGLASS Ionic Interlayer Laminated Glass BS 6206 Class A Impact Performance Technical Note

This CNCGLASS technical note summarizes the soft-body impact performance of architectural laminated safety glass made of 8 mm annealed glass, a 1.52 mm CNCGLASS ionoplast interlayer, and 8 mm annealed glass, evaluated against BS 6206:1981. Four panels, each 865 mm × 1930 mm, were tested; measured overall thicknesses were 17.55 mm, 17.54 mm, 17.53 mm, and 17.55 mm. Each panel was struck at mid-span by the standard soft-bag impactor from drop heights of 305 mm, 457 mm and 1,219 mm, following BS 6206:1981, Appendix A, Clause A.4. The note states that it is a performance summary, not a third-party test certificate or a certificate of conformity, and that it does not authorize the use of any third-party laboratory mark.

At 305 mm and at 457 mm, none of the four panels broke, and they were recorded as Class C and Class B respectively. At 1,219 mm, panel 1 did not break, while panels 2, 3, and 4 broke safely; all four were recorded as Class A. For the panels that fractured, both 8 mm annealed glass plies developed numerous cracks, the ionoplast interlayer held the construction intact, no shear displacement or opening developed within the body of any panel, and the detached-particle mass limits in BS 6206:1981, Clause 5.3(b) were met: the mass of particles detached within three minutes of impact did not exceed the mass equivalent of 10,000 mm² of the original panel, and the largest single detached particle weighed less than the mass equivalent of 4,400 mm². The classification recorded for this construction is Class A. Enquiries can be sent to cnc@cncglass.com.

CNCGLASS-Thermal-Cutter-Blade-11-2-In-Clear-Bag

This short video shows a flat metal blade for a thermal cutter, sealed in a clear bag on white paper marked 11.2. The camera starts close on the blade, then pulls back; a hand briefly enters the frame before a wider view of the bag and the 11.2 mark.

These blades are for a thermal cutter, also called a heat cutter or hot knife, used to trim EVA, PVB, or SGP laminate remains. A CNC@CNCglass.com watermark runs across the frame. Enquiries can be sent to cnc@cncglass.com.

CNCGLASS-Thermal-Cutter-Blade-11-2

This photo set shows a flat metal blade for a thermal cutter, sealed in a clear bag and photographed on white paper marked 11.2. The blade has a pointed cutting tip, a central slot, and a two-pronged mounting end.

These blades are for a thermal cutter, also called a heat cutter or hot knife, used to trim EVA, PVB, or SGP laminate remains. A CNC@CNCglass.com watermark runs across each photo. Enquiries can be sent to cnc@cncglass.com.

CNCGLASS-Many-Uses-of-EVA-Film

This technical article surveys the many uses of EVA film, keeping the focus on laminated glass, photovoltaic encapsulation, and decorative or switchable stacks rather than on footwear, bags, or packaging, even though those wider copolymer uses exist. In laminated glass, EVA is described as the moisture-tolerant interlayer for vacuum-furnace work, decorative inserts, and many outdoor or wet-edge plates. In photovoltaics, it is the usual encapsulant that bonds cells to glass, keeps the optical path open, and stands between the circuit and weather. Decorative EVA and, where specified, PDLC-related stacks extend the same chemistry into partitions and privacy glass. Those three uses share a need for controlled gel content, cleanliness, and a proven cycle. The article argues that when we speak of the many uses of EVA film, we mean the constructions in which a clear, adhesive, cross-linkable sheet earns its place, starting with glass and solar work, and that wider copolymer uses should not crowd out those technical duties.

CNCGLASS-Key-Role-of-EVA-Interlayers

This technical article explains the key role of EVA (ethylene-vinyl acetate) interlayers as a bonding film with a safety job, not a surface sticker. The encapsulant adheres to glass, holds shards after impact, and can add ultraviolet control and a measure of acoustic damping when the stack is designed for those duties. In a collision, an EVA laminate may still crack, but the fragments stay on the film and the opening remains closed, which is why EVA is specified for many architectural interiors, decorative plates, and, in suitable grades, outdoor glass and photovoltaic modules. The article notes that a well-chosen sheet raises the toughness of the plate, that a cross-linking grade forms a more heat-stable network, and that the same film can block a very large share of ultraviolet radiation. Acoustic transmission also falls when a viscoelastic interlayer sits in the path of the sound, more useful in an acoustic or multi-ply build-up than in a thin single interlayer. EVA is also used in furniture glass and in the encapsulation of photovoltaic modules, where long-term adhesion and optical clarity are as important as fragment retention.

CNCGLASS-Two-Workers-Measuring-Silicone-Membrane-On-Floor

This short video shows two workers measuring a CNCGLASS silicone membrane laid on cardboard on the workshop floor. Glass storage racks are visible in the background, and the camera moves along the tape at the edge of the sheet.

Two workers measure a CNCGLASS silicone membrane laid out on cardboard on the workshop floor.

CNCGLASS silicone membranes are used for safety glazing vacuuming, including glass lamination with EVA, PVB, SGP, or TPU. A CNC@CNCglass.com watermark runs across the frame. Enquiries can be sent to cnc@cncglass.com.